成都華臻科技有限責任公司

產 品 說 明 書

 

DDT人體感應開關

一、產品簡介

     本開關是繼手動開關、電子觸摸開關、聲控開關之后推出的智能產品。它接收人體發出的紅外線，當

有人在其探測范圍內活動時便能開啟負載，只要人不離開探測范圍并且在活動，負載就能持續工作，直到人離開后

才延時開關負載。其工作穩定可靠，節能省電，安全方便，是現代智能化高品質生活的理想選擇。

     本開關廣泛應用于庭院、通道、走廊、樓梯、庫房、陽臺、浴室、洗手間等要求方便又節電的場所，是現代化

物業 管理和樓宇智能化的具體表現。

     This product is the newest intellective product in science and technology after the emergence

of the handcontrol switch,the electronic touch switch and the sound-control switch.It receives the

infrared ray emitted by the human body.the service load will be started up when some body moves

about in the detecting area.The service load will keep working when he still moves about in that area.

energy saving,safety and convenience make  it  become  your ideal choice in the modern intellectua-

lized high-quality life.

     This wsitch is extensively applied to the court,the passage,the corridor,the stairs,the depot,

the bathroom,the toilet and so on.It"s the embodiment of real setate management and buiding inte-

llectualization.

二、產品特征

1、全自動人體感應：人到燈亮，人走燈熄;

2、安裝簡易方便，安全省電，省電率大于85％;

3、采用無觸點電子開關，不產生電火花，不干擾其它電器;

4、抗干擾能力特強，待機功耗小，使用壽命長，且能有效延長負載的使用壽命;

5、智能延時，人在探測范圍內活動負載可持續工作;

6、自動測光，白天不工作，晚上或光暗（光度小于2LUX時）才工作。

1.Automatic human sensitivity:The light will be lighted when some body comes,and the  light will

  be  turned off when he leaves.

2.Easy installation,safety and energy saving.The rate of electricity saving is more than 85％

3.Electronic seitch is applied and it won"t cause electricity saprk and inetrfere the other

  electric appliance.

4.Strong anti-interference,low power-wear and long using life.

5.Intellective time-delay.the service load will keep working when some body moves about in the

  detecting area.

6.Auto-through the taking light,it is not working in daytime,it is working at night or luminosity

  less than 2.

 

三、技術參數

1、工作電壓：AC 100V-250V  50Hz-60Hz

2、負載類型：25W-100W  照明燈或排氣扇

3、探測距離：7米以內

4、探測角度：115度

5、延時時間：30秒－60秒（可定做）

6、外觀尺寸：MRT 104－K86

                   86×86×40

1.Working voltage:AC100V-250V  50Hz-60Hz

2.Type of load:25W-200W lamps or exhaust fan

3.Detecting range:7m

4.Detecting angle:115 degree

5.The delay time:30-60 second

6.Appearance measurement:MRT104-K86

                                  86×86×40

四、安裝步驟

注意：安裝前請先切斷電源總開關

 

1、取下壁上原有的標準開關盒的面板;

2、按圖2兩條導線接入本產品的接線柱孔內，擰緊螺絲;

3、在探測范圍內進行行走測試;

4、本產品**佳安裝高度為1.5米左右。

 

Note:please shut off the power supply before installation.

 

1.Take off the cover of the existing normal switch on the wall.

2.Joint wires into the holes of the jointing poles of this switch and fix the screw tightly.

3.To walk in the detecting area to test it.

4.The best installation height is about 1.5m.

 

五、感應范圍實例（SENSITIVE AREA EXAMPLES）

六、注意事項（NOTES）

1、本產品適用于照明燈及排氣扇等，額定負載為25－100W;

2、剛通上電源，燈泡會閃1－3次，再亮約30秒后才開始工作（探測區內應無人走動，測試要在晚上或較暗

   的時候進行）;

3、白色膠片是接收紅外線的透鏡，請勿刮傷，若有污漬請用棉布輕擦干凈，嚴禁按穿;

4、本產品橫向感應較直向感應效果佳;

5、本產品使用時不能直接暴露在無防護的室外露天環境;

1.This product is suitable for lamps,exhaust fans and so on.The rated power is 25-200W.

2.The bulb will flash 1-3 times after the power supply is connected.And it will lights for

  about 30 seconds again.The bulb will start to be in normal working state only after that

  （No one in the  detecting area moves about）.

3.The white film is the lens of receiving the infrared ray,please don"t scratch. Please

  use soft cloths to clean itcarefully when there is besmirched.

4.The transverse sensitivity is better than the straight sensitivity.

5.Don"t expose this product directly to the open area when using it.

               

                                感謝閣下使用DDT產品